• packageimg
packageimg

HV816K6-G

EL Lamp Driver 5.5V 16-Pin QFN EP T/R

Inventory:5,121

  • 90-day after-sales guarantee
  • 365 Days Quality Guarantee
  • Genuine Product Guarantee
  • 7*24 hours service quarantee
  • Part Number : HV816K6-G

  • Package/Case : QFN-16

  • Brands : Microchip Technology

  • Components Categories : Lighting, Ballast Controllers

  • Datesheet : HV816K6-G DataSheet (PDF)

Quick Inquiry

Please submit RFQ for HV816K6-G or email to us: Email: [email protected], we will contact you in 12 hours.

Overview of HV816K6-G

HV816 is a high voltage Electroluminescent (EL) lamp driver designed for driving a lamp capacitance of up to 150nF, or an area of approximately 42 square inches. It is comprised of a boost converter followed by an H-bridge. The boost converter produces a regulated output voltage, which is set at a nominal value of 180V using an internal reference voltage. The H-bridge is used to produce a differential output drive and the EL lamp will therefore see ±180V (360V peak-to-peak). The HV816 has two internal oscillators, one for controlling the boost converter switching frequency and the other for controlling the H-bridge switching frequency. Having separate control of each switching frequency allows flexibility in the circuit design.The operating input supply voltage is 2.7 to 5.5V, but the Enable (EN) and Select (SEL) interface to the device will accept logic high levels down to 1.5V. The EN input is for turning the device ON and OFF. The SEL input is for external logic control of the H-bridge switching frequency, if required. The HV816 boost converter stage uses a single inductor and a minimum number of external components. The input voltage to the inductor can be different from the input voltage to the HV816 (split supply). The external inductor is connected either between the LX and VDD pins or, for split supply applications, between the LX pin and a higher voltage supply (shown as VIN in the Block Diagram). An external MOSFET has to be driven by the switch oscillator to generate a high voltage. The switching frequency for this MOSFET is set by an external resistor connected between the RSW-Osc pin and the supply pin VDD. During operation, the external switching MOSFET turns on and allows energy to be stored in the inductor; this energy is transferred into the capacitor CS when the MOSFET turns off. The voltage at the CS pin will increase with every switching cycle. Once the voltage at the CS pin reaches the desired regulation limit, nominally 180V, the external switching MOSFET is turned OFF to conserve power.The CS capacitor is connected between the CS pin and ground; the CS pin is internally connected to the H-bridge. Energy from the boost converter stage is stored in the capacitor before being transferred to the EL lamp. Depending on the EL lamp sizes, a 1.0nF to 15nF capacitor should be used for CS. The EL lamp switching frequency can be in the range of 100Hz to 1.0kHz. This frequency can be set by either an external logic signal at the SEL pin, with a frequency that is 4 times the desired EL lamp switching frequency, or by an external resistor connected between the REL-Osc and VDD pins. If external frequency is input to the device at the SEL pin, the REL-Osc pin should be connected to ground.The HV816 has the provision to control the discharge rate of the output to minimize audible noise emitted by the EL lamp, which is connected between the VA and VB pins. An external resistor from the RSLEW-OUT pin to ground controls the VA, VB output discharge rate. EL lamp dimming can be accomplished by changing the input voltage to the VREG pin. The VREG pin allows an external voltage source to control the VCS amplitude. The VCS voltage is approximately 143 times the voltage at the VREG pin.

Key Features

    • 360VPP output voltage for high brightness
    • Large output load capability of up to 150nF
    • 2.7 to 5.5V operating supply voltage
    • Single lithium ion cell compatible
    • Adjustable output regulation for dimming
    • External switching MOSFET
    • Low audible noise
    • Output discharge slew rate control
    • 1.5V logic
    • Dedicated Enable pin
    • Two EL frequency controls
    • Independent lamp and converter frequency setting
    • Split supply capability
    • Available in 16-Lead 4x4 QFN package

Specifications

The followings are basic parameters of the part selected concerning the characteristics of the part and categories it belongs to.

Product Status Active Type Dimmable EL Lamp Driver
Frequency 50kHz ~ 200kHz Voltage - Supply 2.7V ~ 5.5V
Current - Supply 2 µA Dimming Yes
Operating Temperature -40°C ~ 85°C Mounting Type Surface Mount
Package / Case QFN-16 Supplier Device Package 16-QFN (4x4)
Base Product Number HV816 Manufacturer Microchip
Product Category Display Drivers & Controllers RoHS Details
Product Drivers Operating Supply Voltage 2.7 V to 5.5 V
Minimum Operating Temperature - 40 C Maximum Operating Temperature + 85 C
Mounting Style SMD/SMT Brand Microchip Technology
Operating Frequency 200 kHz Operating Supply Current 3 mA
Product Type Display Drivers & Controllers Factory Pack Quantity 3300
Subcategory Driver ICs

Warranty & Returns

Warranty, Returns, and Additional Information

  • QA & Return Policy

    Parts Quality Guarantee: 365 days

    Returns for refund: within 90 days

    Returns for Exchange: within 90 days

  • Shipping and Package

    Shipping:For example, FedEx, SF, UPS, or DHL.UPS, or DHL.

    Parts Packaging Guarantee: Featuring 100% ESD anti-static protection, our packaging incorporates high toughness and superior buffering capabilities.

  • Payment

    For example, channels like VISA, MasterCard, UnionPay, Western Union, PayPal, and more.

    If you have specific payment channel preferences or requirements, please get in touch with our sales team for assistance.